Differences

This shows you the differences between two versions of the page.

--- equipment:woodshop:dustextractor [2026/05/17 07:48] – dave
+++ equipment:woodshop:dustextractor [2026/05/27 15:24] (current) – dave
@@ Line 1: / Line 1: @@
 ====== Portable Dust Extractor - Yorklean WV100 ======
-{{:equipment:woodshop:t33a_main_240v.jpg?600|}}
+{{:equipment:woodshop:dustextractor:dust_extractor.jpg?600|}}
 <callout title="No-Induction Required" type="danger" icon="true"> This equipment requires no induction prior to use. </callout>
@@ Line 12: / Line 12: @@
 The WV100 features the well proven dual filtration system (0.5 micron filtration) along with a noise reducing acoustic hood. It’s the ideal extractor for small bench mounted machines such as disc sanders and for power tools. It is compact enough to be stored under a bench.
-Motor	Single phase 1x1200W vacuum motor
+|Motor|Single phase 1x1200W vacuum motor|
-Speed	12500rpm
+|Speed|12500rpm|
-Supply	230V 50Hz on a 13A 3-pin BS approved moulded plug
+|Supply|230V 50Hz on a 13A 3-pin BS approved moulded plug|
-Collection Capacity	35ltr (approx)
+|Collection Capacity|35ltr (approx)|
-Airflow Rate	70 l/sec (+/-5%)
+|Airflow Rate|70 l/sec (+/-5%)|
-Filters	2 stage, up to 0.5 micron
+|Filters|2 stage, up to 0.5 micron|
-Suction	2500mm WG (+/-5%)
+|Suction|2500mm WG (+/-5%)|
-Inlet Size (Internal Diameter)	58mm
+|Inlet Size (Internal Diameter)|58mm|
-Size	370mm diam x 510mm height
+|Size|370mm diam x 510mm height|
-Approx. Weight	10kg
+|Approx. Weight|10kg|
-Noise Level	75dB(A)
+|Noise Level|75dB(A)|
 ==== Introduction ====
-Product Overview:
-{{youtube>v6BhUU8Upk4}}
 Full Instruction Manual:
-{{ :equipment:woodshop:trend_t33a_extractor_manual.pdf |Trend T33A User Manual.pdf}}
+{{ :equipment:woodshop:dustextractor:yorkleen_wv100_manual.pdf |Torkleen WV100 User Manual}}
 ==== Instructions For Use ====
-== Check if the bag needs emptying or changing before and after use. ==
+== Check if the drum needs emptying before and after use. ==
 == Airborne wood dust is hazardous to health. Wood dust should always be vacuumed rather than swept with a brush to avoid creating airborne dust. ==
@@ Line 41: / Line 37: @@
 == Large chips, eg from planing or the wood lathe should be gathered up using the dustpan and brush and binned before vacuuming. ==
-== Do not use without a bag fitted. ==
+== Do not use without the filter protecting bag fitted. ==
 == Do not use without a filter fitted. ==
 == No Wet Use. ==
-This machine is for use with wood dust in the wood workshop, if it is used with liquids it will get gummed up inside.
+This machine is for use with wood dust in the wood workshop.
-Do not use this extractor for liquids ... unless it is an emergency. Instead, use the Charles vacuum from the CNC for liquids.
+**Do not use this extractor for liquids.** Instead, use the Charles vacuum from the CNC for liquids.
-If there is an emergency need to use this for liquids, it has that capability, please read page 10 of the manual for how to set it up. (clean out wood dust, remove bag, change filter) and ensure that you clean and dry the vacuum after use.
-=== Extraction velocity monitor & filter shaker button ===
-If the extraction velocity monitor is red, press and hold the filter shaker button for 3 seconds. (device/extraction must be on) the filter will continue the shaker function for a further 5 seconds after release.
-{{:equipment:woodshop:t33a_feat12_3.jpg?400|}}
 ==== Changing the Bag ====
@@ Line 61: / Line 50: @@
 === Removing the Collection Bag ===
-The collection bag must be replaced when the extraction velocity monitor goes to red and stays on red.
+The collection bag must be replaced monthly as a minimum and is part of the monthly maintenance schedule however, if the bag is damaged or needs replacing sooner please replace it.
-  - Unlock the container catches and remove the lid.
+  - Unlock the container catch and remove the lid.
-  - To remove bag undo the container hose pull bag off the container deflector flange.
+  - Remove the elastic band then remove the bag.
-  - Close the bag by flipping the tab over (fig 4 below).
+  - Replace the bag using one found in the consumables cupboard in the hallway using the elastic band to hold it in position.
+  - Replace the lid and fasten it with the container catch.
   - Dispose of the filter in a suitable container according to the applicable laws.
-  - It is good practice to change the bag regularly to guarantee optimal cooling of the motor.
-{{:equipment:woodshop:screenshot_2024-12-18_150420.png?600|}}
-=== Inserting a new Collection Bag ===
-  - Spare collection bags are kept in the cupboard in the hall. If we are running low, please ask on the consumables forum thread for more to be ordered.
-  - The collection bag has a card-reinforced opening with a tab at the top.
-  - Handle the bag with care to avoid damage.
-  - Insert the collection bag into the container with the opening towards the front of the vacuum cleaner (images below).
-  - Pull the bag opening over the container deflector flange ensuring the collection bag opening passes over the ridge on the container deflector.
-  - Fold out the rest of the bag downwards into the container.
-{{:equipment:woodshop:t33a_feat9_3.jpg?600|}}
-{{:equipment:woodshop:screenshot_2024-12-18_150454.png?400|}}
-=== Power Take off ===
-Auto-Start 1500W Power Tool Take-Off automatically turns the extractor on and off with the connected power tool.
-{{:equipment:woodshop:t33a_feat11_3.jpg?400|}}
-=== Changing the Hepa Filter ===
-{{:equipment:woodshop:t33a_feat8_3.jpg?400|}}