Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
manual:consumables [2026/03/17 19:24] – kitmanual:consumables [2026/06/27 13:55] (current) – dave
Line 35: Line 35:
 ^Item ^Notes ^Known good supplier^ ^Item ^Notes ^Known good supplier^
 |Printer paper| |Printer paper|
-|Solder||https://www.toolstation.com/lead-free-flux-cored-solder/p97854|+|Solder||https://cpc.farnell.com/duratool/d01685/solder-sn99-3-cu0-7-0-7mm-100g/dp/SD01539|
 |Heat shrink| |Heat shrink|
 |Wire| |Wire|
-|De-solder braid| +|De-solder braid 1.5mm||https://cpc.farnell.com/chip-quik/solderwick1-5/solder-wick-1-5mm-5-no-clean-yellow/dp/SD03513| 
-|Flux|+|De-solder braid 2.8mm||https://cpc.farnell.com/chip-quik/solderwick2-8/solder-wick-2-8mm-5-no-clean-blue/dp/SD03515| 
 +|Flux||https://cpc.farnell.com/mg-chemicals/8351-125ml/wave-soldering-flux-bottle-125ml/dp/SD03103|
 |Pens|  |Pens| 
 |pencils| |pencils|
Line 57: Line 58:
 |Drill bits|3, 4, 5, 6, 8 and 10mm brad point bits| |Drill bits|3, 4, 5, 6, 8 and 10mm brad point bits|
 |Dowels||https://www.toolstation.com/wooden-dowel/p75364| |Dowels||https://www.toolstation.com/wooden-dowel/p75364|
-|Forsner bits|10 - 50 mm|+|Forsner bits|10 - 50 mm in 5mm increments|
 |Screwdriver bits|PZ2, PZ3, T15, T20, T25, S4.5, S5.5| |Screwdriver bits|PZ2, PZ3, T15, T20, T25, S4.5, S5.5|
 |Hole bits|21, 25, 29, 38, 44, 51 and 64 mm diameter| |Hole bits|21, 25, 29, 38, 44, 51 and 64 mm diameter|
-|CNC Flat Endmill 1/4 Inch Cut - 1/4 Inch Shank Extended Reach|Carbide3D Bit Equivalent 201|https://ooznest.co.uk/product/solid-carbide-end-mills-square-2flute-up/| +|CNC Flat Endmill 1/4 Inch Cut - 1/4 Inch Shank Extended Reach|Carbide3D Bit Equivalent 201|https://ooznest.co.uk/product/1-4-up-cut-standard-general-purpose-square-end-router-bit-1-4-shank/| 
-|CNC Flat Endmill 1/8 Inch Cut - 1/8 Inch Shank Standard|Carbide3D Bit Equivalent 102|https://ooznest.co.uk/product/solid-carbide-end-mills-square-2flute-up/| +|CNC Flat Endmill 1/8 Inch Cut - 1/8 Inch Shank Standard|Carbide3D Bit Equivalent 102|https://ooznest.co.uk/product/1-8-up-cut-standard-general-purpose-square-end-router-bit-1-8-shank/| 
-|CNC Ball endmill 1/4 Inch Cut - 1/4 Inch Shank Standard|Carbide3D Bit Equivalent 202|https://ooznest.co.uk/product/solid-carbide-ball-end-mills-2-flute-up-cut-uk/| +|CNC Ball endmill 1/4 Inch Cut - 1/4 Inch Shank Standard|Carbide3D Bit Equivalent 202|https://ooznest.co.uk/product/1-4-standard-general-purpose-ball-end-router-bit-1-4-shank/| 
-|CNC Ball endmill 1/8 Inch Cut - 1/8 Inch Shank Standard|Carbide3D Bit Equivalent 101|https://ooznest.co.uk/product/solid-carbide-ball-end-mills-2-flute-up-cut-uk/| +|CNC Ball endmill 1/8 Inch Cut - 1/8 Inch Shank Standard|Carbide3D Bit Equivalent 101|https://ooznest.co.uk/product/1-8-standard-general-purpose-ball-end-router-bit-1-8-shank/| 
-|CNC V-Bit 90 Degree|SKU 45704 - Carbide3D Bit Equivalent 301|https://ooznest.co.uk/product/amana-tool-carbide-tipped-end-mills-v-groove/| +|CNC V-Bit 90 Degree|SKU 45704 - Carbide3D Bit Equivalent 301|https://ooznest.co.uk/product/1-2-x-90-amana-tool-45704-decorative-carbide-tipped-v-groove-router-bit-1-4-shank/| 
-|CNC V-Bit 60 Degree|SKU 45705 - Carbide3D Bit Equivalent 302|https://ooznest.co.uk/product/amana-tool-carbide-tipped-end-mills-v-groove/|+|CNC V-Bit 60 Degree|SKU 45705 - Carbide3D Bit Equivalent 302|https://ooznest.co.uk/product/1-2-x-60-amana-tool-45705-decorative-carbide-tipped-v-groove-router-bit-1-4-shank/|
 --- ---
 |Table router bit - 1/2 inch shank|Roundover Bit - 1/2 inch|https://www.axminstertools.com/axcaliber-ovolo-cutter-d-38-x-19-r-12-7mm-s-1-2-12-7mm-666055| |Table router bit - 1/2 inch shank|Roundover Bit - 1/2 inch|https://www.axminstertools.com/axcaliber-ovolo-cutter-d-38-x-19-r-12-7mm-s-1-2-12-7mm-666055|
 |Table router bit - 1/2 inch shank|Roundover Bit - 3/4 inch|https://www.axminstertools.com/axcaliber-ovolo-cutter-d-50-8-x-25-4-r-19-05mm-s-1-2-12-7mm-666150| |Table router bit - 1/2 inch shank|Roundover Bit - 3/4 inch|https://www.axminstertools.com/axcaliber-ovolo-cutter-d-50-8-x-25-4-r-19-05mm-s-1-2-12-7mm-666150|
-|Table router bit - 1/2 inch shank|Dovetail - 14° slope|https://www.axminstertools.com/axcaliber-dovetail-router-cutter-d-22-2-x-22-2mm-k-14-s-1-2-12-7mm-666019|+|*Table router bit - 1/2 inch shank|Dovetail - 14° slope|https://www.axminstertools.com/axcaliber-dovetail-router-cutter-d-22-2-x-22-2mm-k-14-s-1-2-12-7mm-666019|
 |Table router bit - 1/2 inch shank|Chamfer Bit - 45° 47.5mm|https://www.axminstertools.com/axcaliber-chamfer-cutter-bearing-guided-d-47-6-x-20mm-s-1-2-12-7mm-666161| |Table router bit - 1/2 inch shank|Chamfer Bit - 45° 47.5mm|https://www.axminstertools.com/axcaliber-chamfer-cutter-bearing-guided-d-47-6-x-20mm-s-1-2-12-7mm-666161|
 |Table router bit - 1/2 inch shank|Rabbeting bit with interchangeable bearings|https://www.axminstertools.com/axcaliber-rebate-cutter-set-d-34-92-x-12-7mm-s-1-2-12-7mm-666163| |Table router bit - 1/2 inch shank|Rabbeting bit with interchangeable bearings|https://www.axminstertools.com/axcaliber-rebate-cutter-set-d-34-92-x-12-7mm-s-1-2-12-7mm-666163|
 |Table router bit - 1/2 inch shank|Flush trim - 1 1/4 inch top bearing|https://www.axminstertools.com/axcaliber-flush-trim-cutter-top-bearing-d-19-05-x-31-75mm-s-1-2-12-7mm-bearing-19mm-666090| |Table router bit - 1/2 inch shank|Flush trim - 1 1/4 inch top bearing|https://www.axminstertools.com/axcaliber-flush-trim-cutter-top-bearing-d-19-05-x-31-75mm-s-1-2-12-7mm-bearing-19mm-666090|
 |Table router bit - 1/2 inch shank|Flush trim - 2 inch bottom bearing|https://www.axminstertools.com/axcaliber-flush-trim-cutters-bottom-bearing-d-12-7-x-50-8mm-s-1-2-12-7mm-666105| |Table router bit - 1/2 inch shank|Flush trim - 2 inch bottom bearing|https://www.axminstertools.com/axcaliber-flush-trim-cutters-bottom-bearing-d-12-7-x-50-8mm-s-1-2-12-7mm-666105|
-|Trim router bit - 1/4 inch shank|Roundover Bit - 3/8 inch|https://www.axminstertools.com/axcaliber-ovolo-cutter-d-31-75-x-15-88-r-9-53mm-s-1-4-6-35mm-666052|+|*Trim router bit - 1/4 inch shank|Roundover Bit - 3/8 inch|https://www.axminstertools.com/axcaliber-ovolo-cutter-d-31-75-x-15-88-r-9-53mm-s-1-4-6-35mm-666052|
 |Trim router bit - 1/4 inch shank|Roundover Bit - 1/4 inch|https://www.axminstertools.com/axcaliber-ovolo-cutter-d-25-4-x-11-11-r-6-35mm-s-1-4-6-35mm-666050| |Trim router bit - 1/4 inch shank|Roundover Bit - 1/4 inch|https://www.axminstertools.com/axcaliber-ovolo-cutter-d-25-4-x-11-11-r-6-35mm-s-1-4-6-35mm-666050|
 |Trim router bit - 1/4 inch shank|Roundover Bit  1/8 inch|https://www.axminstertools.com/axcaliber-ovolo-cutter-d-19-05-x-9-53-r-3-2mm-s-1-4-6-35mm-666047| |Trim router bit - 1/4 inch shank|Roundover Bit  1/8 inch|https://www.axminstertools.com/axcaliber-ovolo-cutter-d-19-05-x-9-53-r-3-2mm-s-1-4-6-35mm-666047|
Line 82: Line 83:
 |Trim router bit - 1/4 inch shank|Flush trim - 1 inch top bearing|https://www.axminstertools.com/axcaliber-flush-trim-cutters-top-bearing-d-15-88-x-25-4mm-s-1-4-6-35mm-bearing-16mm-666109| |Trim router bit - 1/4 inch shank|Flush trim - 1 inch top bearing|https://www.axminstertools.com/axcaliber-flush-trim-cutters-top-bearing-d-15-88-x-25-4mm-s-1-4-6-35mm-bearing-16mm-666109|
 |Trim router bit - 1/4 inch shank|Flush trim - 1 inch bottom bearing|https://www.axminstertools.com/axcaliber-flush-trim-cutters-bottom-bearing-d-12-7-x-25-4mm-s-1-4-6-3mm-666101| |Trim router bit - 1/4 inch shank|Flush trim - 1 inch bottom bearing|https://www.axminstertools.com/axcaliber-flush-trim-cutters-bottom-bearing-d-12-7-x-25-4mm-s-1-4-6-3mm-666101|
-|Trim router bit - 1/4 inch shank|Flush trim - 10mm bottom bearing|https://www.axminstertools.com/axcaliber-milling-cutter-with-top-bearing-952561|+|Trim router bit - 1/4 inch shank|Milling cutter - 10mm top bearing|https://www.axminstertools.com/axcaliber-milling-cutter-with-top-bearing-952561|
 --- ---
 |Forstner Bit 6mm shank|10mm|https://www.axminstertools.com/axcaliber-forstner-bit-10mm-501920| |Forstner Bit 6mm shank|10mm|https://www.axminstertools.com/axcaliber-forstner-bit-10mm-501920|
Line 109: Line 110:
 ===Metal Shop=== ===Metal Shop===
 ^Item ^Notes ^Known good supplier^ ^Item ^Notes ^Known good supplier^
-|Drill bits|3, 4, 5, 6, 8 and 10mm|+|Drill bits|2-10mm in half sizes|
 |step drill| |step drill|
 |Hacksaw blades| |Hacksaw blades|
  • manual/consumables.1773775457
  • Last modified: 4 months ago
  • by kit