Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
| manual:consumables [2026/01/19 20:30] – dave | manual:consumables [2026/03/17 19:24] (current) – kit | ||
|---|---|---|---|
| Line 68: | Line 68: | ||
| --- | --- | ||
| |Table router bit - 1/2 inch shank|Roundover Bit - 1/2 inch|https:// | |Table router bit - 1/2 inch shank|Roundover Bit - 1/2 inch|https:// | ||
| - | |Table router bit - 1/2 inch shank|Roundover Bit - 3/8 inch|https:// | + | |Table router bit - 1/2 inch shank|Roundover Bit - 3/4 inch|https:// |
| |Table router bit - 1/2 inch shank|Dovetail - 14° slope|https:// | |Table router bit - 1/2 inch shank|Dovetail - 14° slope|https:// | ||
| |Table router bit - 1/2 inch shank|Chamfer Bit - 45° 47.5mm|https:// | |Table router bit - 1/2 inch shank|Chamfer Bit - 45° 47.5mm|https:// | ||
| Line 74: | Line 74: | ||
| |Table router bit - 1/2 inch shank|Flush trim - 1 1/4 inch top bearing|https:// | |Table router bit - 1/2 inch shank|Flush trim - 1 1/4 inch top bearing|https:// | ||
| |Table router bit - 1/2 inch shank|Flush trim - 2 inch bottom bearing|https:// | |Table router bit - 1/2 inch shank|Flush trim - 2 inch bottom bearing|https:// | ||
| - | |Trim router bit - 1/4 inch shank|Straight Bit - 25mm |https:// | ||
| |Trim router bit - 1/4 inch shank|Roundover Bit - 3/8 inch|https:// | |Trim router bit - 1/4 inch shank|Roundover Bit - 3/8 inch|https:// | ||
| |Trim router bit - 1/4 inch shank|Roundover Bit - 1/4 inch|https:// | |Trim router bit - 1/4 inch shank|Roundover Bit - 1/4 inch|https:// | ||
| Line 84: | Line 83: | ||
| |Trim router bit - 1/4 inch shank|Flush trim - 1 inch bottom bearing|https:// | |Trim router bit - 1/4 inch shank|Flush trim - 1 inch bottom bearing|https:// | ||
| |Trim router bit - 1/4 inch shank|Flush trim - 10mm bottom bearing|https:// | |Trim router bit - 1/4 inch shank|Flush trim - 10mm bottom bearing|https:// | ||
| + | --- | ||
| + | |Forstner Bit 6mm shank|10mm|https:// | ||
| + | |Forstner Bit 8mm shank|15mm|https:// | ||
| + | |Forstner Bit 8mm shank|20mm|https:// | ||
| + | |Forstner Bit 8mm shank|25mm|https:// | ||
| + | |Forstner Bit 8mm shank|30mm|https:// | ||
| + | |Forstner Bit 10mm shank|35mm|https:// | ||
| + | |Forstner Bit 10mm shank|40mm|https:// | ||
| + | |Forstner Bit 10mm shank|45mm|https:// | ||
| + | |Forstner Bit 10mm shank|50mm|https:// | ||
| --- | --- | ||
| |Band saw blades|Standard blade 1/2", length 93 1/4" / 2370mm 6 tpi. More info on the [[equipment: | |Band saw blades|Standard blade 1/2", length 93 1/4" / 2370mm 6 tpi. More info on the [[equipment: | ||
| Line 90: | Line 99: | ||
| |Masking tape| | |Masking tape| | ||
| |Carpenters pencils| | |Carpenters pencils| | ||
| + | |Compass| | ||
| |Belt sander belts | 6" x 48" (150 x 1220mm) | Machine Mart https:// | |Belt sander belts | 6" x 48" (150 x 1220mm) | Machine Mart https:// | ||
| |Belt sander disks | 230mm diameter | Machine Mart https:// | |Belt sander disks | 230mm diameter | Machine Mart https:// | ||
| Line 103: | Line 113: | ||
| |Hacksaw blades| | |Hacksaw blades| | ||
| |Bandsaw blades|1638mm (64 1/2") x 1/2" 14 tpi|https:// | |Bandsaw blades|1638mm (64 1/2") x 1/2" 14 tpi|https:// | ||
| - | |Angle grinder disks|| | ||
| - | |Bench Grinder wheels| Coarse on the left, fine on the right | | ||
| - | |Sorby sharpening belts|60, | ||
| |Hex & Torx keys|| | |Hex & Torx keys|| | ||
| |Screwdrivers|| | |Screwdrivers|| | ||
| |Lathe Bits| Parting off, centre drills, indexable carbide bits| | |Lathe Bits| Parting off, centre drills, indexable carbide bits| | ||
| - | ===COSH Cupboard=== | + | ===COSHH Cupboard=== |
| ^Item ^Notes ^Known good supplier^ | ^Item ^Notes ^Known good supplier^ | ||
| |WD-40|| | |WD-40|| | ||
| Line 122: | Line 129: | ||
| ^Item ^Notes ^Known good supplier^ | ^Item ^Notes ^Known good supplier^ | ||
| |Flux Welding Wire|SIP MIG Gasless Flux Cord Welding Wire|https:// | |Flux Welding Wire|SIP MIG Gasless Flux Cord Welding Wire|https:// | ||
| + | |Angle grinder disks|| | ||
| + | |Bench Grinder wheels| Coarse on the left, fine on the right | | ||
| + | |Sorby sharpening belts|60, | ||
| ===Craft Room=== | ===Craft Room=== | ||