Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
equipment:woodshop:woodcnc [2026/05/30 11:21] – daveequipment:woodshop:woodcnc [2026/06/08 18:21] (current) – matt
Line 1: Line 1:
-======Wood CNC - Shapeoko 3 XL -Not yet commissioned======+======Wood CNC - Shapeoko 3 XL ======
  
 <callout title="Induction Required" type="danger" icon="true">This equipment requires an induction prior to use. For your own safety and to avoid damage to the equipment do not attempt to use it until you have been inducted.</callout> <callout title="Induction Required" type="danger" icon="true">This equipment requires an induction prior to use. For your own safety and to avoid damage to the equipment do not attempt to use it until you have been inducted.</callout>
Line 5: Line 5:
 <callout title="Crush and flying debris Hazard" type="warning" icon="true">Keep fingers away from moving parts. Risk of flying debris (e.g. tool crash).</callout> <callout title="Crush and flying debris Hazard" type="warning" icon="true">Keep fingers away from moving parts. Risk of flying debris (e.g. tool crash).</callout>
  
-<callout title="PPE Required" type="primary" icon="true">This equipment requires the use of hearing protection during use.</callout>+<callout title="PPE Required" type="primary" icon="true">This equipment requires the use of hearing protection during use, and finger protection when changing bits</callout>
  
  
Line 34: Line 34:
 {{:equipment:woodshop:woodcnc:r1.jpg?direct&600|}} {{:equipment:woodshop:woodcnc:r1.jpg?direct&600|}}
  
-{{:equipment:woodshop:woodcnc:r2.jpg?direct&600|}}+{{:equipment:woodshop:r2-2.jpg?direct&600|}}
  
 {{:equipment:woodshop:woodcnc:r3.jpg?direct&600|}} {{:equipment:woodshop:woodcnc:r3.jpg?direct&600|}}
Line 88: Line 88:
 ====3. Clamping Down your Stock==== ====3. Clamping Down your Stock====
  
-Before you clamp down your stock, move the router out of your way:+ 
 +NOTE: All items for the CNC including probe pins, router bits, collets spanners and allen key can be found in the small draw under the Raspberry Pi and returned here after use. 
 + 
 +*****Before you clamp down your stock, move the router out of your way:
  
   * Press the "Jog" button at the top of the Carbide Create window to open the Jog Screen.   * Press the "Jog" button at the top of the Carbide Create window to open the Jog Screen.
Line 193: Line 196:
  
 ====How to Change Router Bits or Probe Pins==== ====How to Change Router Bits or Probe Pins====
 +
 +The cutting edges of bits can be sharp so gloves should be worn when changing bits.
  
 To install a router bit or probe pin: To install a router bit or probe pin:
Line 206: Line 211:
   * Make sure that the bottom of your bit or pin does not protrude more than 150mm below the bottom of the aluminum bracket that holds the router. There is a helpful L-shaped guide in the drawer to assist when measuring this.   * Make sure that the bottom of your bit or pin does not protrude more than 150mm below the bottom of the aluminum bracket that holds the router. There is a helpful L-shaped guide in the drawer to assist when measuring this.
   * Hold the yellow button on the side of the router, and use a 17mm spanner to firmly tighten the collet nut.   * Hold the yellow button on the side of the router, and use a 17mm spanner to firmly tighten the collet nut.
- 
-Probe pins, router bits, and collets must be stored in the small draw under the Raspberry Pi. 
  
 {{:equipment:woodshop:woodcnc:six_inches.jpg?direct&600|}} {{:equipment:woodshop:woodcnc:six_inches.jpg?direct&600|}}
  • equipment/woodshop/woodcnc.1780140097
  • Last modified: 5 weeks ago
  • by dave