Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
equipment:woodshop:woodcnc [2026/04/30 17:56] – mattequipment:woodshop:woodcnc [2026/09/11 10:22] (current) – fraserh
Line 1: Line 1:
-====== Wood CNC - Shapeoko 3 XL -Not yet commissioned====== +======Wood CNC - Shapeoko 3 XL ======
-===== Page under construction ===== +
-*add picture here+
  
 <callout title="Induction Required" type="danger" icon="true">This equipment requires an induction prior to use. For your own safety and to avoid damage to the equipment do not attempt to use it until you have been inducted.</callout> <callout title="Induction Required" type="danger" icon="true">This equipment requires an induction prior to use. For your own safety and to avoid damage to the equipment do not attempt to use it until you have been inducted.</callout>
Line 7: Line 5:
 <callout title="Crush and flying debris Hazard" type="warning" icon="true">Keep fingers away from moving parts. Risk of flying debris (e.g. tool crash).</callout> <callout title="Crush and flying debris Hazard" type="warning" icon="true">Keep fingers away from moving parts. Risk of flying debris (e.g. tool crash).</callout>
  
-<callout title="PPE Required" type="primary" icon="true">This equipment requires the use of eye protection / hearing protection / respiratory protection during use.</callout>+<callout title="PPE Required" type="primary" icon="true">This equipment requires the use of hearing protection during use, and finger protection when changing bits</callout>
  
-====== Materials ====== + 
-==== Cutting Items====+======Introduction===== 
 + 
 +Our CNC Router is a Shapeoko 3 XL. 
 + 
 +The router has a usable bed size of 800mm X 350mm. 
 + 
 +We have 1/4" and 1/8" collets for the router, and a small collection of bits for basic operations. For anything more complex (or to guarantee a sharp bit) you should use your own router bits. 
 + 
 +The router is driven using Carbide Motion, which is loaded on the Raspberry Pi the wooden box beside it. 
 + 
 +The router is protected by an online induction. To get inducted, read this page carefully, then take the quiz on the membership system. 
 + 
 +This wiki page will explain the basics of how to safely set up and run a simple job on the router. It will not teach you how to design things for the router, prepare files for cutting. 
 + 
 +To learn more about the router, including how to design and prepare files for it, check out these videos by the manufacturer:  
 + 
 +  * [[https://carbide3d.com/hub/courses/getting-started-cnc/|Carbide3D Getting Started with CNC]] - A text and video series that will give you a simple introduction to the world of CNC. 
 +  * [[https://carbide3d.com/hub/courses/jumpstart/|Carbide3D Jumpstart course]] - A text and video series that takes you through designing and making several projects. 
 +  * [[https://www.youtube.com/carbide3d|Carbide 3D YouTube Page]] - Contains a large number of helpful videos with guides and tips. 
 + 
 +For first time CNC users, we recommend using the free version of Carbide Create to design and prepare your files, as this software comes pre-programmed with the parameters of our machine and our communial bits. 
 + 
 +======Parts and Layout===== 
 + 
 +{{:equipment:woodshop:woodcnc:r1.jpg?direct&600|}} 
 + 
 +{{:equipment:woodshop:r2-2.jpg?direct&600|}} 
 + 
 +{{:equipment:woodshop:woodcnc:r3.jpg?direct&600|}} 
 + 
 + 
 +====== Permitted Materials ====== 
 + 
 +You can work with the following materials on the CNC router:
   * Hard wood   * Hard wood
   * Soft wood   * Soft wood
Line 18: Line 49:
   * Delryn   * Delryn
  
-====Banned Items====+You must NOT work with these materials:
   * Metal   * Metal
 +  * Humans
  
-====== Shapeoko 3 XL – Glossary of Terms ======+====== Tools Provided ======
  
-Most definitions here are adapted from Carbide3D’s video series, with small changes for our machine and accessories.\\ +To aide members in using the CNC for the first time we have provided a small selection of tools. These tools were selected because they match tools within the Carbide Create Tool Library making it easier to program you tool paths.
-**Tip:** These are the basics you’ll need for your induction quiz. Links to the original videos are at the bottom if you want to go deeper.+
  
-==== Core Concepts ====+The tools provided are:
  
-**CNC** – //Computer Numerical Control//\\ +<WRAP 600px left> 
-A computer-controlled machine that moves a cutting tool with high precision. Our laser cutter, 3D printers, and vinyl cutter are also CNC machines.+^ Bit Type ^ Mill Size ^ Carbide3D Bit Equivalent ^ 
 +| Flat Endmill | 1/4 Inch Cut - 1/4 Inch Shank | 201 | 
 +| Flat Endmill | 1/8 Inch Cut - 1/8 Inch Shank | 102 | 
 +| Ball Endmill | 1/4 Inch Cut - 1/4 Inch Shank | 202 | 
 +| Ball Endmill | 1/8 Inch Cut - 1/8 Inch Shank | 101 | 
 +| V-Bit | 90 Degree | 301 | 
 +| V-Bit | 60 Degree | 302 | 
 +| Downcut Flat Endmill | 1/4 Inch Cut - 1/4 Inch Shank | 251 | 
 +</WRAP> 
 +<WRAP clear/>
  
-**CAD** – //Computer-Aided Design//\\ +We would recommend that anyone planning to use the CNC more that once should look at purchasing their own tools.  
-Software used to design your part. You draw shapes, add features, and prepare them for cutting.   +
-  * **We use:** Carbide Create (free version is fine)   +
-  * **Why it matters:** This is where you create the geometry of your project.+
  
-**CAM** – //Computer-Aided Manufacturing//\\ +====== Usage Insturctions ======
-Software that converts your CAD design into movement instructions for the CNC.   +
-  * **We use:** Carbide Motion (pre-installed on the workshop Raspberry Pi)   +
-  * **Why it matters:** This is the “translator” between your design and the machine.+
  
-**G-code**   +====1. Pre-Useage Checks====
-The text-based “language” CNC machines read. Generated automatically by CAD/CAM software. You don’t need to write it manually.+
  
-==== Machine Movement ====+Before you use the CNC Router, it's important to open the cabinet doors and check the following:
  
-**Axes**   +  * That the drive belts look in good condition, with no cuts of frays. 
-  * **X:** Left ↔ Right   +  * There is not a thick dust build up on top of the big silver gantries. 
-  * **Y:** Front ↔ Back   +  * That there is nothing inside the enclosure that could interfere or jam the movement of the router.
-  * **Z:** Up ↔ Down   +
-//Tip: Y has the “Y rails” and Z is the vertical axis — that leaves X as side-to-side.//+
  
-**Home Position** – The fixed point the machine returns to after startup.\\ +You also need to check that:
-**Work Zero** – Your chosen starting point for a specific job (usually a corner or centre of the stock).+
  
-==== Design Files ====+  * The fire extinguisher is present in the woodshop. 
 +  * The dust collector bag is not full.
  
-**Vector Graphics**\\ +If you see anything wrong with the condition of the machine, don't use it and let the committee know on the forum.
-Drawings made of lines and points (e.g., SVG files). Ideal for CNC because the machine can follow their coordinates exactly.+
  
-**Toolpaths**\\ +====2. Starting the Machine and Software====
-The routes your cutter will follow. Defined in CAD, turned into G-code in CAM.+
  
-==== Materials & Workholding ====+  * Log into the machine with your card/fob (once you've passed the induction). The enclosure lights should turn on when you log in. 
 +  * If the Raspberry Pi is not already running, press the silver power button to boot it up. Note that the screen may not immediately respond when you press the button. 
 +  * If the emergency stop button has been pressed, rotate it clockwise to reset it.
  
-**Stock** – The material you’re cutting.\\ +Once the Raspberry Pi has booted:
-**Spoilboard** – A sacrificial board under the stock to protect the machine.\\ +
-**Workholding** – Clamps or other methods to secure your stock so it doesn’t move.+
  
-==== Cutting Parameters ====+  * Start the "Carbide Motion" software by pressing the raspberry button in the top left of the screen → Office → Carbide Motion.  
 +  * In Carbide Motion, press the "Connect to cutter" button 
 +  * Press the "Initialise Machine" button. 
  
-**Feed Rate** – How fast the cutter moves through the material (X/Y).\\ +The router will now move to the rear rightmost point, and will then move to the front right.
-**Plunge Rate** – How fast the cutter moves down into the material (Z).\\ +
-**Spindle Speed** – How fast the bit spins (RPM), adjusted on the router dial.\\+
  
-//Why it matters:// These three settings determine cut quality and safety. Carbide Create has safe starting values for common materials.+{{:equipment:woodshop:woodcnc:1_office_carbide_motion.png?direct&400|}}
  
-==== Tools & Cutters ====+====3. Clamping Down your Stock====
  
-**End Mill / Bit** – The cutting tool.   
-  * **Flat End Mill** – Flat tip, general-purpose cutting.   
-  * **Ball End Mill** – Rounded tip, for 3D contours and smooth finishes.   
-  * **V-Cutter** – Angled tip, ideal for engraving and sign work.   
-  * **Fly Cutter** – Large flat cutter for surfacing spoilboards or material tops. 
  
-**Flutes** – The cutting edges on a bit. More flutes = smoother cut, fewer flutes = faster removal.+NOTE: All items for the CNC including probe pins, router bits, collets spanners and allen key can be found in the small draw under the Raspberry Pi and returned here after use.
  
-**Upcut / Downcut** – Direction of flute spiral:   +*****Before you clamp down your stock, move the router out of your way:
-  * **Upcut:** Pulls chips up and away (better chip removal, but can lift stock).   +
-  * **Downcut:** Pushes chips down (better surface finish, but can trap chips).+
  
-**Shank size** – the size of the diameter of the solid part of the bit, two sizes are currently supported by our router:     +  * Press the "Jog" button at the top of the Carbide Create window to open the Jog Screen. 
-  * **1/8** - 1/8 inch (3.175mm). +  * From the Jog Screen, use the buttons on the screen or the USB pendant to move the router out of your way.
-  * **1/4** - 1/4 inch (6.35mm).+
  
-----+  * Place your stock on the spoilboard. Use the small "stop blocks" on one side to position your stock and align it with the grid of holes. 
 +  * Use the Crush-It clamps on the opposite side of your stock to hold it securely. To do this. first loosen (but don't remove) the small screws on the front of the clamps, position the clamps tightly against your stock, bolt the clamps to the spill board, then tighten the front screw to push the clamp face firmly against the stock. 
 +  * Double-check that your stock is firmly attached to the spillboard by trying to move it. If there is any movement, you should re-clamp it.
  
-==== Machining Types ====+Tip: The stop blocks have smooth and serated sides, and the Crush-It clamps have replacable smooth and serrated jaws. The serrated surfaces give better grip but can leave marks on some stock.
  
-**2D Machining** – Cutting shapes at a constant depth.\\ +Tip: Make sure the clamps don't block your toolpath!
-**2.5D Machining** – Multiple depths, but cutting one flat layer at a time (e.g., pockets + cutouts).\\ +
-**3D Machining** – Machine moves in X, Y, and Z simultaneously to create complex curves.\\+
  
-==== Safety ====+Tip: Use bolts of the correct length to fix the clamps to the spillboard. If the bolts are too long they will bottom out in the threaded holes.
  
-**Emergency Stop (E-stop)** – Red button to immediately stop the machine.\\ +NOTE: Don't over tighten the clamps as they will pull the clamping point through the spoil board.
-**PPE** – Safety glasses, hearing protection, dust mask.\\ +
-**Dust Collection** – Removes chips and dust from the work area.+
  
-====== More Info About This Machine ======+{{:equipment:woodshop:woodcnc:spoilboard_clamp_issue.jpg?400|}}
  
-These videos are a great resource for information about this machine:+====4. Probing your Stock Location====
  
-  * [[https://carbide3d.com/hub/courses/getting-started-cnc/|Carbide3D Getting Started with CNC]] - A text and video series that will give you a simple introduction to the world of CNC. +We have a BitZero probe kit, which we use to accurately locate corner of your stock is and how tall it is. This is known as setting the "Work Zero". The kit consists of a probe pin, a probe plate, and a magnetic earth connection. To use the BitZero:
-  * [[https://carbide3d.com/hub/courses/jumpstart/|Carbide3D Jumpstart course]] - A text and video series that takes you through designing and making several projects. +
-  * [[https://www.youtube.com/carbide3d|Carbide 3D YouTube Page]] - Contains a large number of helpful videos with guides and tips.+
  
-====== Usage Instructions ======+  * Remove the dust shoe (it's magnetically attached and just pulls downwards) 
 +  * Install a probe pin into the router collet (using the instructions for installing router bits and probe pins at the bottom of this page). 
 +  * Place the probe plate on your stock so so that is tight to the front left corner.  
 +  * From the Jog Screen, use the buttons on the screen or the USB pendant to position the router so that the tip of the probe is within the circular hole in the probe plate. 
 +  * Attach the magnetic earth to the router collet. 
 +  * From the Jog Screen, press Probe. A pop-up window will open. 
 +  * Press "Corner" then on the next screen, press "Begin Probe".
  
-==== Pre-Useage Checks ====+The router will move slowly to identify the sides of the circular hole with the probe pin, then it will lift out of the hole and tap the top of the probe plate. 
  
-  * Open the machine doors and check that the drive belts look in good condition, with no cuts of frays.\\ +When it has finished doing this, a pop-up window will ask you to remove the magnetic earth.
-  * Check that there is no thick dust build up on top of the big silver gantry's. +
-  * Check that there is nothing left loose inside the enclosure that could jam the movement of the router. +
-  * Check the fire extinguisher is present in the woodshop.+
  
-==== Powering up the machine ====+  * Remove the magnetic earth from the router collet. 
 +  * Press the Ok button.
  
-  * Log into the machine with your card/fob (once you've passed the induction). The enclosure lights should turn on when you log in.\\ +The router will now move to the front-right and touch the probe pin to the height probe on the machine's frame. This completes the probe operation.
-  * If the Raspberry Pi is not already running, press the silver button to boot it up.\\ +
-  * If the emergency stop button has been pressed, rotate it clockwise to reset it.\\+
  
-==== Starting the Software and Initialising the Machine ====+{{:equipment:woodshop:woodcnc:6_check_probe.jpg?400|}} 
 +{{:equipment:woodshop:woodcnc:8_corner.png?400|}}
  
-  * Start the Carbide Motion software by pressing the raspberry button in the top left -> Office -> Carbide Motion\\ +====5. Loading your File====
-  * Press the "Connect to cutter" button\\ +
-  * Press on "Initialise Machine". The router will move to the rear rightmost point first and will then move to the front allowing you to install the probe pin or cutting bit.\\+
  
-==== Installing probe pin ====+  * Insert your USB drive into USB port on the front of the Raspberry Pi case. 
 +  * Cancel the "Removable Medium" pop-up menu.
  
-First install the correct collet for the size you’ll be using: +  * Press "Run" at the top of the Carbide Create window to open the Job Info Screen 
-  * Use a 17 mm spanner to loosen the collet nut on the bottom of the router.  +  * Press "Load New File" on the Job Info Screen. 
-  * Press and hold the yellow spindle lock button (on the lower right of the router) to stop the shaft from spinning.  +  * In the Open File pop-up, navigate to your USB drive (computer → / → media → cncuser → your USB drive) and open your .C2D file.
-  * Remove the collet nut and old collet together. +
-  * Fit the new collet and collet nut, using the same process in reverse.+
  
-Then choose the probe pin that matches the size of the the collet you’ve just fitted. The probe pins are straight metal rods. Insert the pin into the collet and tighten the nut by hand. +Tip: You can sanity-check your file is correct by switching to the Top View tab.
  
-Use the measuring guide to check the pin isn’t sticking out too far. Once correct, hold the spindle lock and tighten the nut with the 17 mm spanner. 
  
-==== Clamping down stock ====+====6. Starting your Job====
  
-In Carbide Motion press the Jog button to enter the Jog Screen. You can use the buttons on the screen or the pendant to move the router around.+  * Press "Start Job" on the Job Info Screen. 
 +  * On the pop-up, press "Start"
  
-Place your stock on the spoilboard so it’s aligned with the grid. The spoilboard has threaded holes spaced 100 mm apart, and the grid lines are aligned with the machine’s X and Y motion. This makes it easy to square your stock with the router’s movement.+The spindle will now move to the front-right, and a new pop-up will ask you to install your first bit.
  
-Use the small stop blocks on one side to position the stock — each block has two smooth sides and two with small serrations. The serrated sides give better grip but can leave small marks on the stock.+  * Install your first router bit into the router (using the instructions for installing router bits and probe pins at the bottom of this page). 
 +  * Re-fit the magnetic dust shoe. 
 +  * Switch on the dust collector. 
 +  * Open the blast gate for the CNC router, and close the blast gates for any machines that are not in use. 
 +  * Close the cabinet doors. 
 +  * Press the "Resume" button on the pop-up.
  
-Use the Crush-It clamps on the opposite side to hold the stock securely. Each clamp has replaceable front jaws (smooth or serrated) for different materials. Loosen, but don’t remove, the front screw on the clamp. Position the clamp tight against the stock and bolt it down. Then tighten the front screw to push the clamp face firmly against the stock.+The spindle will now spin up, and a new pop-up will ask you to check the speed setting on the router.
  
-Make sure the clamps don’t block the toolpath and use bolts of the correct length — too long and they can bottom out in the threaded holes. Tighten evenly so the stock sits flat and secure.+  * Check the speed dial on the router matches the requested speed in the pop-up. 
 +  * If it doesn't, open the cabinet doors, change the speed, and close them again. 
 +  * Press "Resume".
  
-======Walkthrough======+After a brief pause, the job will begin.
  
-Turn on isolator and boot raspberry PI.+{{:equipment:woodshop:woodcnc:19_fit_dust_shoe.jpg?400|}} 
 +{{:equipment:woodshop:woodcnc:18_tool_change.png?400|}}\\ 
 +{{:equipment:woodshop:woodcnc:20_spindle.jpg?400|}} 
 +{{:equipment:woodshop:woodcnc:21_resume.png?400|}}
  
-Turn on red emergency button if needed+====7. While the Machine is Running====
  
-Start Carbide Motion by clicking the raspberry button in the top left -> Office -> Carbide Motion+The machine MUST be closely supervised at all times when running. This is to ensure:
  
-{{:equipment:woodshop:woodcnc:1_office_carbide_motion.png?400|}}+  * The workpiece remains firmly clamped 
 +  * The machine doesn't jam or get stuck 
 +  * The extraction is clearing dust effectively 
 +  * There is no risk of fire
  
-Click the connect to cutter button+Opening the door during the job will pause the machine and show a pop-up. To resume the job, close the doors and press "Resume" on the pop-up. This is useful if you need to check your clamps or remove detritus.
  
-{{:equipment:woodshop:woodcnc:2_connect_to_cutter.png?400|}}+Hitting the E-stop button during the job will kill the power to the controller and spindle.
  
-Give the CNC a visual check to make sure everything looks OK+====8. Changing Bit During a Job====
  
-Click initialise machine and the spindle moves forward+Some jobs require more than one bit to complete, and you will be asked to change bits partway through.
  
-{{:equipment:woodshop:woodcnc:3_initialise_machine.png?400|}}+When this happens, the router will move to the front-right of the cabinet and spin down. A pop-up will ask you to install the new bit and then set the new speed in exactly the same way as you did for your first bit at the start of the job.
  
-Remove dust shoe using clip on right and using the 17mm spanner and the yellow locking button on the side of the router fit the probe pin which is the same size as your bit bearing in mind you might have to change between the 1/8 and ¼ collet.+====9. After your Job====
  
-{{:equipment:woodshop:woodcnc:4_fit_probe_pin.jpg?400|}}+When you're finished, you should always: 
 +  * Clear any waste or debris from the cabinet. 
 +  * Log out of the machine by pressing the button on the RFID box. 
 +  * Shut down the Raspberry Pi if the machine isn't going to be used again soon.
  
-In Carbide Create press the Jog button in the top menu and using either the on screen pad or the pendant, move the router to the back of the enclosure.+====How to Change Router Bits or Probe Pins====
  
-{{:equipment:woodshop:woodcnc:5_jog.png?400|}}+The cutting edges of bits can be sharp so gloves should be worn when changing bits.
  
-Clamp stock to bed making sure it doesn’t move+To install a router bit or probe pin: 
 +  * Remove the dust shoe. 
 +  * Hold the yellow button on the side of the router and use a 17mm spanner to loosen the collet nut. 
 +  * Once the collet is loose, you can withdraw the bit or pin currently installed.
  
-Move the router into the bottom left corner, attach the probe magnet and touch the probe to the probe plate and you should see a red light.+  * We have a 1/4" and 1/8" collet, to suit different bits. If you need to swap to the other collet: 
 +     * Continue to unscrew the collet nut until the collet and nut can be removed from the router. 
 +     * Screw the other collet and nut into the router in it's place.
  
-{{:equipment:woodshop:woodcnc:6_check_probe.jpg?400|}}+  * Insert the new bit or pin into the collet. 
 +  * Make sure that the bottom of your bit or pin does not protrude more than 150mm below the bottom of the aluminum bracket that holds the router. There is a helpful L-shaped guide in the drawer to assist when measuring this. 
 +  * Hold the yellow button on the side of the router, and use a 17mm spanner to firmly tighten the collet nut.
  
-Put the probe plate tight to the bottom left of your stock and using the jog screen or the pendant move the probe into the circle in the probe plate.+{{:equipment:woodshop:woodcnc:six_inches.jpg?direct&600|}}
  
-{{:equipment:woodshop:woodcnc:7_probe.png?400|}}+====== Glossary of Common CNC Terms ======
  
-In Carbide Motion click Probe -> corner -> Begin Probe+Most definitions here are adapted from Carbide3D’s video series, with small changes for our machine and accessories.\\ 
 +**Tip:** These are the basics you’ll need for your induction quiz. Links to the original videos are at the bottom if you want to go deeper.
  
-{{:equipment:woodshop:woodcnc:8_corner.png?400|}} +==== Core Concepts ====
-{{:equipment:woodshop:woodcnc:9_begin_probe.png?400|}}+
  
-Remove magnet and probe plate when it asks you to remove ground clip.+**CNC** – //Computer Numerical Control//\\ 
 +A computer-controlled machine that moves a cutting tool with high precision. Our laser cutter, 3D printers, and vinyl cutter are also CNC machines.
  
-{{:equipment:woodshop:woodcnc:10_remove_magnet.jpg?400|}} +**CAD** – //Computer-Aided Design//\\ 
-{{:equipment:woodshop:woodcnc:11_bit_setter.jpg?400|}}+Software used to design your part. You draw shapes, add features, and prepare them for cutting.   
 +  * **We use:** Carbide Create (free version is fine)   
 +  * **Why it matters:** This is where you create the geometry of your project.
  
-Make sure you are clear from the CNC as the head will move then you click OK.+**CAM** – //Computer-Aided Manufacturing//\\ 
 +Software that converts your CAD design into movement instructions for the CNC.   
 +  * **We use:** Carbide Motion (pre-installed on the workshop Raspberry Pi)   
 +  * **Why it matters:** This is the “translator” between your design and the machine.
  
-{{:equipment:woodshop:woodcnc:12_bit_zero_ok.png?400|}}+**G-code**   
 +The text-based “language” CNC machines read. Generated automatically by CAD/CAM software. You don’t need to write it manually.
  
-Go back to run menu+==== Machine Movement ====
  
-Plug in USB stick and click cancel to the popup.+**Axes**   
 +  * **X:** Left ↔ Right   
 +  * **Y:** Front ↔ Back   
 +  * **Z:** Up ↔ Down   
 +//Tip: Y has the “Y rails” and Z is the vertical axis — that leaves X as side-to-side.//
  
-{{:equipment:woodshop:woodcnc:13_usb_cancel.png?400|}}+**Home Position** – The fixed point the machine returns to after startup.\\ 
 +**Work Zero** – Your chosen starting point for a specific job (usually a corner or centre of the stock).
  
-Click the load new file button and navigate to computer -> / -> media -> cncuser -> your USB drive and confirm from description that you have loaded the correct file, there are some preview tabs to see what is going to be cut, when you're happy press Done.+==== Design Files ====
  
-{{:equipment:woodshop:woodcnc:14_load_file.png?400|}} +**Vector Graphics**\\ 
-{{:equipment:woodshop:woodcnc:15_open_file.png?400|}} +Drawings made of lines and points (e.g., SVG files). Ideal for CNC because the machine can follow their coordinates exactly.
-{{:equipment:woodshop:woodcnc:16_done.png?400|}}+
  
-press start job.+**Toolpaths**\\ 
 +The routes your cutter will follow. Defined in CAD, turned into G-code in CAM.
  
-{{:equipment:woodshop:woodcnc:17_start_job.png?400|}}+==== Materials & Workholding ====
  
-Then press start on next screen+**Stock** – The material you’re cutting.\\ 
 +**Spoilboard** – A sacrificial board under the stock to protect the machine.\\ 
 +**Workholding** – Clamps or other methods to secure your stock so it doesn’t move.
  
-Spindle will move to front right and the screen will ask you to fit your first bit, fit bit, make sure bit doesn’t stick out lower than the bitsetter measurer. you might need to adjust height of dust shoe.+==== Cutting Parameters ====
  
-Fit the dust shoe, close doors and press resume.+**Feed Rate** – How fast the cutter moves through the material (X/Y).\\ 
 +**Plunge Rate** – How fast the cutter moves down into the material (Z).\\ 
 +**Spindle Speed** – How fast the bit spins (RPM), adjusted on the router dial.\\
  
-{{:equipment:woodshop:woodcnc:19_fit_dust_shoe.jpg?400|}} +//Why it matters:// These three settings determine cut quality and safety. Carbide Create has safe starting values for common materials.
-{{:equipment:woodshop:woodcnc:18_tool_change.png?400|}}+
  
-Spindle will spin up and there will be a message to set the speed dial. If the dial is correct just hit resume, if you need to change it open the door, the spindle will stop, set the speed, close the door and hit resume+==== Tools & Cutters ====
  
-{{:equipment:woodshop:woodcnc:20_spindle.jpg?400|}} +**End Mill / Bit** – The cutting tool.   
-{{:equipment:woodshop:woodcnc:21_resume.png?400|}}+  * **Flat End Mill** – Flat tip, general-purpose cutting.   
 +  * **Ball End Mill** – Rounded tip, for 3D contours and smooth finishes.   
 +  * **V-Cutter** – Angled tip, ideal for engraving and sign work.   
 +  * **Fly Cutter** – Large flat cutter for surfacing spoilboards or material tops.
  
-The first job will start and start cutting.+**Flutes** – The cutting edges on a bit. More flutes = smoother cut, fewer flutes = faster removal.
  
-{{:equipment:woodshop:wood22_running_job.png?400|}}+**Upcut / Downcut** – Direction of flute spiral:   
 +  * **Upcut:** Pulls chips up and away (better chip removal, but can lift stock).   
 +  * **Downcut:** Pushes chips down (better surface finish, but can trap chips).
  
-====== When The Machine is Running ======+**Shank size** – the size of the diameter of the solid part of the bit, two sizes are currently supported by our router:     
 +  * **1/8** - 1/8 inch (3.175mm). 
 +  * **1/4** - 1/4 inch (6.35mm).
  
-The machine MUST be closely supervised at all times when running. This is to ensure: +==== Machining Types ====
-  * The workpiece stays firmly clamped +
-  * The machine doesn't jam or get stuck +
-  * The extraction clears dust effectively +
-  * There is no risk of fire +
- +
-If you open while the machine is in use, it will pause the job and show the message below. You can close the doors and press start to resume where you left off. This is useful if you need to remove detritus or check that your clamps are secure.+
  
-{{:equipment:woodshop:woodcnc:23_release_freehold.png?400|}} +**2D Machining** – Cutting shapes at a constant depth.\\ 
- +**2.5D Machining** – Multiple depths, but cutting one flat layer at a time (e.g., pockets + cutouts).\\ 
-Hitting the E-stop button will kill the power to the controller and spindle. +**3D Machining** – Machine moves in X, Y, and Z simultaneously to create complex curves.\\
- +
-{{:equipment:woodshop:woodcnc:5_jog.png?400|}}+
  • equipment/woodshop/woodcnc.1777571815
  • Last modified: 6 months ago
  • by matt