Differences

This shows you the differences between two versions of the page.

--- equipment:woodshop:bandsaw [2024/02/27 21:04] – Begin adding photos. nough
+++ equipment:woodshop:bandsaw [2024/11/19 21:42] (current) – external edit 127.0.0.1
@@ Line 35: / Line 35: @@
   * Ear defenders for ear protection
   * Dust masks for prevention of inhalation of particulate matter
-  * Do not wear gloves while using the bandsaw. They should only be used when [[Changing the blade]].
+  * Do not wear gloves while using the bandsaw. They should only be used when [[equipment:woodshop:bandsaw#Changing the bandsaw blade|Changing the bandsaw blade]].
 ==== Bandsaw blades ====
   * **The Hackspace provides a single bandsaw blade size**. This policy is intended to make the bandsaw more reliable, and will be reviewed at the Q2 2024 members meeting.
-  * You can use a blade of your own choosing when you visit the hackspace, but you **MUST** return the original blade back in to a good condition (cutting well and true) before leaving - leave at least 10 minutes to do this. See [[Changing the blade]] (section) and the {{ :equipment:woodshop:bandsaw:replacing_the_blade.docx |Induction Manual}} (until changed and updated)
+  * You can use a blade of your own choosing when you visit the hackspace, but you **MUST** return the original blade back in to a good condition (cutting well and true) before leaving - leave at least 10 minutes to do this. See [[equipment:woodshop:bandsaw#Changing the bandsaw blade|Changing the bandsaw blade]] and the {{ :equipment:woodshop:bandsaw:replacing_the_blade.docx |Induction Manual}} (until changed and updated)
   * <del>The spares are located on the wall besides the bandsaw.</del>
-  * If a bandsaw blade becomes blunt, replace with a spare from the wall. Do not use the spares if the blade is still sharp - if it's not cutting well, see the section on [[cutting tips]].
+  * If a bandsaw blade becomes blunt, replace with a spare from the wall. Do not use the spares if the blade is still sharp - if it's not cutting well, see the section on [[equipment:woodshop:bandsaw#Not cutting straight|Not cutting straight]].
   * If there are no more spares, buy a replacement(s) and request reimbursement via the forum (Or request a replacement be bought on the forum consumables thread).
   * The bandsaw takes blades 93-1/4 inch = 2368.55mm
@@ Line 100: / Line 100: @@
 === Changing the bandsaw blade ===
+[[https://www.youtube.com/watch?v=ZFAPniN2zrk|How to unfold and fold the blade.]]
   - Find suitable gloves to protect your hands. Even blunt blades can cause damage.
   - Loosen the knob at the top right on the front of the bandsaw.
@@ Line 116: / Line 119: @@
   - "Uncoil" the new blade so that it has only one loop, not the three loops that it comes packaged in.
   - Put the new blade into the machine by reversing steps 6 through 10, ensuring the teeth are pointing down on the side you insert into the table bit. You are likely to need help to get the blade around the pulleys and through the guides all at the same time.
+  - Begin tightening the pulleys
+The below steps needed to finish replacing the blade are also covered under [[equipment:woodshop:bandsaw#Preparation on arrival to the wood shop|Preparation on arrival to the wood shop]].
   - Tighten the pulleys until there is enough tension (as described in the induction).
   - Manually turn the top pulley to ensure proper alignment of the blade with respect to the pulleys, i.e. the blade stays on the middle of the pulley. If it shifts forwards or backwards with respect to the pulley, adjust the angle of pulley wheel by turning the small black knob on the back of the machine as appropriate. If three complete revolutions can be made and the blade stays in the center of the pulley wheel, then it is aligned properly.
@@ Line 143: / Line 149: @@
   * Check that the blade tension is correct for the blade. This can be adjusted with the knob on top of the bandsaw. The guide at the back of the bandsaw tells you when tension is set correctly. You match the red indicator to the line that states the saw size (1/2" currently).
-{{ :equipment:woodshop:20240226_-_bandsaw_tension.jpg?200 |}}
+{{ :equipment:woodshop:20240226_-_bandsaw_tension.jpg?400 |}}
-  * Check that the blade tracking is set correctly. This is done with the clearly labelled knob on the back of the bandsaw. The gullet of the teeth should be at the centre of the wheel. Turning clockwise tilts the top wheel of the bandsaw backwards, moving the blade backwards. The blade will only move after the wheels have been rotated a little, so test by changing the tracking, rotating the wheels by hand, then checking again.
+  * Check that the blade tracking is set correctly. This is done with the clearly labelled knob on the back of the bandsaw. The gullet of the teeth should be at the centre of the wheel. Turning clockwise tilts the top wheel of the bandsaw backwards, moving the blade backwards. The blade will only move after the wheels have been rotated a little, so test by changing the tracking, rotating the wheels by hand, then checking again. If the blade has not moved forwards or backwards after three full rotations of the wheels, then it is stable.
-{{ :equipment:woodshop:20240226_-_bandsaw_blade_tracking.jpg?200 |}}
+{{ :equipment:woodshop:20240226_-_bandsaw_blade_tracking.jpg?400 |}}
   * Align the fence to the table. Note that the fence is attached to the rail at the front with two screws. The fence needs to be aligned to the blade/table and then secured with these screws. So, make sure that the fence is positioned correctly **and** securely attached. The below images how two ways to check alignment, one using the engineers square from the metal shop, and one by eye against the tracks in the table.
-{{ :equipment:woodshop:20240226_-_bandsaw_fence_alignment_esquare.jpg?200 |}}
+{{ :equipment:woodshop:20240226_-_bandsaw_fence_alignment_esquare.jpg?400 |}}
-{{ :equipment:woodshop:20240226_-_bandsaw_fence_alignment_table.jpg?200 |}}
+{{ :equipment:woodshop:20240226_-_bandsaw_fence_alignment_table.jpg?400 |}}
+  * Align the the table to the blade. The table can be tilted to allow angled cuts, and may not have been returned to dead flat. Use the engineers square from the metal shop to confirm that the table is dead square to the blade. The handle unlocks the tilting, while the knob *should* tilt the table. This can often be stiff.
+{{:equipment:woodshop:20240226_-_bandsaw_table_at_angle.jpg?400|}}{{:equipment:woodshop:20240226_-_bandsaw_table_square.jpg?400|}}{{:equipment:woodshop:20240226_-_bandsaw_table_angle_adjustment.jpg?400|}}
 === Preparation for each cut ===
-  * Loosen the guard knob and raise or lower the guard to the height of the work piece. Allow about 1 cm (or less) as tolerance and so that you can actually move the wood through the saw. **Re-tighten the knob so that the guard no longer moves.**
+  * Loosen the guard knob and raise or lower the guard to the height of the work piece. Allow about 1 cm (or less) as tolerance and so that you can actually move the wood through the saw. **Re-tighten the knob so that the guard no longer moves.** The closer the guard is to the workpiece, the less deflection is possible in the blade during your cut, and therefore the straighter the cut will be.
-((Photos to be inserted)
+{{ :equipment:woodshop:20240226_-_bandsaw_guard_controls.jpg?400 |}}
+  * Tilt the table, if needed. See above for details. Please return to dead flat after you have done so.
   * Move the fence to the desired width. There are measurements on the table to give relevant widths. If you need to change the rotation of the fence for lower clearance, ensure you realign the fence to the blade (further up the page). Alternatively, if you are using the angle tray sled thing, move the fence entirely out of the way.
+{{ :equipment:woodshop:20240226_-_bandsaw_fence_on_side.jpg?400 |}}
   * Adjust the gates on the [[Dust Extractor]] so that there is a direct path to the bandsaw. Turn it on.
-  * Ensure you have enough outfeed space for your work piece. **Insert Picture**. If there is not enough space, move the bandsaw.
+  * Ensure you have enough outfeed space for your work piece. If there is not enough space, move the bandsaw.
+{{ :equipment:woodshop:20240226_-_bandsaw_outfeed_correct.jpg?400 |}}
+{{ :equipment:woodshop:20240226_-_bandsaw_outfeed_incorrect.jpg?400 |}}
+Changing wood speed
 === Cutting ===