Differences

This shows you the differences between two versions of the page.

--- equipment:metalshop:mill:3dtouchoffprobe [2025/12/20 15:42] – ↷ Page moved from equipment:cnc:mill:3dtouchoffprobe to equipment:metalshop:mill:3dtouchoffprobe kit
+++ equipment:metalshop:mill:3dtouchoffprobe [2025/12/20 15:42] (current) – ↷ Links adapted because of a move operation kit
@@ Line 6: / Line 6: @@
 The 3D touch-off probe is an electronic touching off probe that can touch off in all X, Y, and Z axis:
-{{:equipment:cnc:mill:cnc-3dprobe-image.png?400|}}
+{{equipment:metalshop:mill:cnc-3dprobe-image.png?400|}}
 It is best used currently using the pendant jog control and is powered via a cable attached to the main control panel.
@@ Line 15: / Line 15: @@
 The 3d probe box and cable live inside  the CNC mill tool cabinet:
-{{:equipment:cnc:mill:cnc-3dprobe-cab.png?400|}}
+{{equipment:metalshop:mill:cnc-3dprobe-cab.png?400|}}
-{{:equipment:cnc:mill:cnc-3dprobe-box.png?400|}}
+{{equipment:metalshop:mill:cnc-3dprobe-box.png?400|}}
-{{:equipment:cnc:mill:cnc-3dprobe-device.png?400|}}
+{{equipment:metalshop:mill:cnc-3dprobe-device.png?400|}}
 Please make sure you return the probe to its carry case and the cable back into the box to ensure we don't lose these very specific cable.
@@ Line 24: / Line 24: @@
 Install the probe into a 6mm collet:
-{{:equipment:cnc:mill:cnc-3dprobe-6mm.png?400|}}
+{{equipment:metalshop:mill:cnc-3dprobe-6mm.png?400|}}
 and mount in the spindle to hand tight (just like when using the wiggler).
 The cable plugs into the front control panel into the very clearly labelled socket:
-{{:equipment:cnc:mill:cnc-3dprobe-socket-location.png?400|}}
+{{equipment:metalshop:mill:cnc-3dprobe-socket-location.png?400|}}
 The plug can only be inserted in one orientation:
-{{:equipment:cnc:mill:cnc-3dprobe-socket.png?200|}}
+{{equipment:metalshop:mill:cnc-3dprobe-socket.png?200|}}
-{{:equipment:cnc:mill:cnc-3dprobe-cable-installed.png?200|}}
+{{equipment:metalshop:mill:cnc-3dprobe-cable-installed.png?200|}}
 The other end of the cable plugs into the 3d probe (which should be in the spindle collet by this point:
-{{:equipment:cnc:mill:cnc-3dprobe-green.png?400|}}
+{{equipment:metalshop:mill:cnc-3dprobe-green.png?400|}}
 If everything is plugged in correctly then the probe should light up green.
@@ Line 47: / Line 47: @@
 Touching off is just like using the wiggler, move the probe around using the jog controls (either pendant or control panel) until the probe touches by turning RED either side of something:
-{{:equipment:cnc:mill:cnc-3dprobe-side.png?400|}}
+{{equipment:metalshop:mill:cnc-3dprobe-side.png?400|}}
 or the top of something:
-{{:equipment:cnc:mill:cnc-3dprobe-top.png?400|}}
+{{equipment:metalshop:mill:cnc-3dprobe-top.png?400|}}
 You can use the fine control jog settings of the pendant (the right hand knob) to really creep up on touching off.