Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
equipment:metalshop:metallathe:howto:cutthreadsl2r [2024/08/15 11:57] – ralawrenceequipment:metalshop:metallathe:howto:cutthreadsl2r [2024/11/19 21:42] (current) – external edit 127.0.0.1
Line 1: Line 1:
 ===== How to cut Threads using the Left to Right Method. ===== ===== How to cut Threads using the Left to Right Method. =====
 +
 +
 +
 +
 +
 +**__//THIS IS WORK IN PROGRESS//__**
 +
 +
 +
 +
  
 Please note this guide is specific to Bristol Hackspace’s Harrison M250 Metal Lathe. Please note this guide is specific to Bristol Hackspace’s Harrison M250 Metal Lathe.
Line 25: Line 35:
 1. Remove the cover plate with an M3 hex key. 1. Remove the cover plate with an M3 hex key.
  
-2. Use an M24 spanner on the end of the Lead Screw to rotate it until the edges of the cover become visible. Only pull the spanner towards you do not try to go in the other direction you will unscrew the nut of the end of the Lead Screw.+2. Rotate the Lead Screw until the edges of the cover become visible. 
  
-3. Push the edge of the cover upwards to reveal the Shear Pin. You may need to use the spanner to rotate the lead screw further.+3. Push the edge of the cover upwards to reveal the Shear Pin. You may need to rotate the lead screw further.
  
 4. Now by rotating the Chuck by hand locate the slot for the Shear Pin to slide in to. Make sure you have the Traverse Direction knob set to forward. 4. Now by rotating the Chuck by hand locate the slot for the Shear Pin to slide in to. Make sure you have the Traverse Direction knob set to forward.
Line 73: Line 83:
 Move the Carriage etc. so that the tool is well away from everything. Set the Lathe going and as the Gauge come around to one of the numbers gently lift the Threading Handle up and you should feel it engage. The Carriage should move from left to right. Move the Carriage etc. so that the tool is well away from everything. Set the Lathe going and as the Gauge come around to one of the numbers gently lift the Threading Handle up and you should feel it engage. The Carriage should move from left to right.
  
-__**Step 9. Test thread spacing.**__+__**Step 9. Set up the DRO.**__
  
-__**Step 10. Set up the DRO.**__ 
  
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +__**Step 10. Test thread spacing.**__
 +
 +Blacken the surface where the thread will be using a marker pen. With the Lathe running bring the cutting tool in to the lightest contact with the stock at the left end of area to be cut. When the Threading Indicator comes around to one of the numbers gentle lift the Threading Handle and it will engage. A trace of the tread will now be visible on the stock. Check this is the correct spacing either with a ruler or a threading measurement gauge.
 + 
 ====Stage 3. Cutting the thread.==== ====Stage 3. Cutting the thread.====
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
 +
  
  
  • equipment/metalshop/metallathe/howto/cutthreadsl2r.1723723073
  • Last modified: 5 months ago
  • (external edit)