Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
equipment:hotworks:welder [2025/03/04 13:48] – ollieequipment:hotworks:welder [2025/03/04 14:25] (current) – ollie
Line 12: Line 12:
    
 Please note, this is a work in progress. Please do not use the welder until inducted - thanks, Ollie Please note, this is a work in progress. Please do not use the welder until inducted - thanks, Ollie
 +Feel free to add to this page, any comments welcome
 +
 ===== Induction ===== ===== Induction =====
  
 Prior to using the welder, you must attend an in-person induction. Please post on the forum if you want an induction. Should be starting spring 2025 Prior to using the welder, you must attend an in-person induction. Please post on the forum if you want an induction. Should be starting spring 2025
  
-Prior to an induction, please have a quick read through the welder manual, and read this wiki page. +Prior to an induction, please have a quick read through the welder manual, and read this wiki page. There is PPE provided, however the risk assessment requires that inductees bring their own respirator to protect from fumes
  
 Induction notes are here - [[equipment:hotworks:welder:induction_notes|]] Induction notes are here - [[equipment:hotworks:welder:induction_notes|]]
Line 31: Line 33:
   * Have a bucket of sand next to the welding bench, which can quickly and safely extinguish minor flames with minimal cleanup   * Have a bucket of sand next to the welding bench, which can quickly and safely extinguish minor flames with minimal cleanup
   * The roller shutter doors **must** remain open during welding operations, and kept open until fumes have cleared   * The roller shutter doors **must** remain open during welding operations, and kept open until fumes have cleared
-  * Fume extraction **must** be used at all times, and kept on until fumes have cleared. Check fume extractor has not been used for general extraction or hoovering - open the top and ensure there are no flammable items inside (eg sawdust)+  * Fume extraction should be used at all times, and kept on until fumes have cleared. Check fume extractor has not been used for general extraction or hoovering - open the top and ensure there are no flammable items inside (eg sawdust)
   * **After welding, you MUST remain in the space for at least 1 hour, checking the area for smouldering items or fires. If you cannot wait the hour, do not weld**   * **After welding, you MUST remain in the space for at least 1 hour, checking the area for smouldering items or fires. If you cannot wait the hour, do not weld**
  
Line 65: Line 67:
   * Welding hood or mask. There are three hanging up, just outside the hot works area. Link to manual [[https://www.clarkeservice.co.uk/manuals/welding_accessories/PG4_Headshield_Iss_3.pdf]]   * Welding hood or mask. There are three hanging up, just outside the hot works area. Link to manual [[https://www.clarkeservice.co.uk/manuals/welding_accessories/PG4_Headshield_Iss_3.pdf]]
   * Closed footwear   * Closed footwear
 +  * The risk assessment also specifies a respirator, to protect from fumes
  
 These are the minimum requirements. You may also need additional PPE for other related tasks, such as eye protection when using an angle grinder.  These are the minimum requirements. You may also need additional PPE for other related tasks, such as eye protection when using an angle grinder. 
Line 76: Line 79:
 ===Welder=== ===Welder===
  
-The Hackspace welder is a Clarke MIG160EN, with an adjustable welding current between 30 and 150 Amps. This is enough to weld 5mm mild steel, and to blow holes through thinner stuff. +The Hackspace welder is a Clarke MIG160EN
  
 Link to manual - [[https://www.clarkeservice.co.uk/manuals/mig_welders/MIG160EN_Mig_Welder_REV_8.pdf]] Link to manual - [[https://www.clarkeservice.co.uk/manuals/mig_welders/MIG160EN_Mig_Welder_REV_8.pdf]]
  
 +__Welder settings__
  
 +Review the manual for a table showing recommended gas settings. Additional trial and error will be required to get the right setting.
  
  
-== Gas vs Gasless welding==+__Gas vs Gasless welding__ 
 The welder is designed for both gas MIG and Gasless welding, however in the Hackspace all welding shall be the gasless type. This uses wire with a flux core to prevent oxidisation and contamination of the weld pool. The welder is designed for both gas MIG and Gasless welding, however in the Hackspace all welding shall be the gasless type. This uses wire with a flux core to prevent oxidisation and contamination of the weld pool.
 Whilst the welder can operate as a standard MIG (ie with Gas) the Hackspace does permit compressed cylinders. The risk assessment for the welding has not considered the use of shielding gas, so for the foreseeable, all welding shall be gasless Whilst the welder can operate as a standard MIG (ie with Gas) the Hackspace does permit compressed cylinders. The risk assessment for the welding has not considered the use of shielding gas, so for the foreseeable, all welding shall be gasless
  
 +
 +__Welder polarity__
 +
 +The welder should remain in the "no gas" configuration. The torch is connected to the negative terminal (-ve), with the earthing cable connected to the positive (+ve) terminal.
 +
 +__Loading wire__
 +
 +The welder manual explains this best, however it will be shown in the induction
  
 ===Fume extractor=== ===Fume extractor===
  
-The fume extractor is an Extractability Protectavac by Weldability. It must be used at all times during welding, to help keep fume levels low+The fume extractor is an Extractability Protectavac by Weldability. It should be used at all times during welding, to help keep fume levels low
 Link to product page - [[https://www.weldability-sif.com/products/extractability/ext1vacmax230/]] Link to product page - [[https://www.weldability-sif.com/products/extractability/ext1vacmax230/]]
  
 [photos to be added here at a later date, to show instructions for operation and maintenance] [photos to be added here at a later date, to show instructions for operation and maintenance]
 +
 +
 +
 +===== Consumables =====
 +The following items will be proposed, for inclusion on the consumable list. Wire and tips will be required frequently, however torch shrouds shouldn't need replacement often
 +//For the time being, I'll provide wire and tips, just to get inductions started - Ollie//
 +
 +  * Welding wire. Flux cored "gasless" wire, 0.8mm diameter, 0.45kg reel. [[https://www.toolstation.com/sip-mig-gasless-flux-cord-welding-wire/p13760]] or similar
 +  * Welding torch tips. 0.8mm diameter, pack of 5. [[https://www.toolstation.com/sip-mig-contact-tips-08mm/p96874]] or similar
 +  * Welding torch shroud. [[https://www.toolstation.com/sip-conical-mig-shrouds/p11948]] or similar
  
  • equipment/hotworks/welder.1741096139
  • Last modified: 9 days ago
  • by ollie